Skip to main content

Plumbing hours: Mon to Sat, 8 am to 7 pm

Plumbing from $80

5.0 out of 5.Rated 5.0 on Google

5.0 out of 5.Rated 5.0 on Google

Plumbing

Plumbing Fixture Installation in St. John's and Area

Plumbing fixture installation in St. John's and area replaces an old fixture with a better one. Think of a lower-flow toilet in place of an old 13-litre one, a shower valve that holds its temperature, frost-free outside taps and quarter-turn shut-offs. Fixture work is plumbing, booked with HomeBrill from $80.

  • Starting at $80
  • Mon to Sat, 8 am to 7 pm
  • Call or text, no account needed

Book plumbing fixture upgrades

No account needed. HomeBrill calls or texts you back to set a time for the visit.

Plumbing starts at $80. When HomeBrill calls or texts you back, ask about the price of your job before a time is set. Privacy: see the privacy policy. This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

Plumbing fixture installation in St. John's: one-piece white vanity top with a moulded basin, an overflow slot, a pop-up drain and a single-hole chrome faucet Plumbing fixture installation in St. John's: one-piece white vanity top with a moulded basin, an overflow slot, a pop-up drain and a single-hole chrome faucet

Problems and parts

When a fixture is worth upgrading

Most fixtures are upgraded at one of three moments: the old one fails, its parts are no longer made, or the walls are open for a renovation. Open walls make the pipes behind them easy to reach. A cracked toilet tank, a shower that swings hot and cold, an outside tap that split last winter or a stuck shut-off each gives a chance to fit something better.

The usual reasons are listed below. Repairs to the fixtures you have are on their own pages: toilet repair and installation, shower and bathtub repair and faucet and sink installation. Hooking up a new washer or dishwasher to its water and drain is booked as appliance installation. Plumbing with HomeBrill in St. John's lists every plumbing job.

What you notice, and the usual causes

Shower runs hot or cold when someone flushes
An older valve with no pressure balancing, so a drop on the cold side changes the mix.
Toilet uses a lot of water, or clogs often
An older design using 13 litres or more a flush, or an early low-flow model with a weak flush.
Outside tap split over the winter
A standard hose bib holding water in the cold part of the wall, often with a hose left attached.
Shut-off valve that will not close, or drips at the stem
An old multi-turn valve that seized or wore after years without being turned.
Pipes bang when a tap snaps shut
Water hammer: water stopped suddenly by a valve that closes hard, with nothing to absorb the shock.
A shower trim you want to change
Trim kits fit only their own brand and valve, so a new look often means a new valve inside the wall.
Scale on taps and shower heads, on a well
Hard well water leaving minerals behind; a softener or filter treats it at the supply.
A faucet whose parts are no longer made
An older model whose cartridge is out of production, so a new faucet is the practical fix.

Parts and materials involved

  • High-efficiency and dual-flush toilets Lower-flow toilets, some with a second, lighter flush.
  • Toilet flange and seal The floor fitting the toilet bolts to, and the seal fitted new each time.
  • Pressure-balancing valve Holds the hot and cold mix steady when pressure on one side drops.
  • Thermostatic valve Holds a set water temperature, with the flow controlled separately.
  • Shower trim kit The handle, faceplate and spout that match one valve.
  • Frost-free outdoor tap A long-stem hose bib whose valve closes inside the heated wall.
  • Quarter-turn shut-off valves Ball-type stops that close in one movement, for sinks, toilets and the main.
  • Water hammer arrestor A small sealed chamber that cushions the shock when a valve closes hard.
  • Leak sensors and automatic shut-off Floor sensors that tell a motorized valve on the main to close.
  • Bidet seat Replaces the toilet seat and takes water from the toilet's supply through a tee.

Pricing

What a fixture upgrade costs

Plumbing with HomeBrill begins at $80, the published starting price. An upgrade's price depends on the fixture and what sits behind it, so name the fixture and send a photo if you can. Ask what the job will cost before a time is set. Settle who supplies the fixture on that call too.

A toilet going onto a sound flange is simpler than one on a cracked flange. A shower trim that fits the existing valve is small work, while a new valve means opening the wall, and tile makes that a larger job. While the water is off, adding quarter-turn stops, new supply lines or a water hammer arrestor can make sense in the same visit.

Plumbing starts at
$80
Your job
Describe it when you call or text, and ask about its price before a time is set

plumbing fixture upgrades

Measure before you buy

Most upgrades that go wrong are fit problems found on the day. A new faucet has to suit the holes in the sink or counter, which the faucet page explains. A shower trim kit fits only its own maker's valve, so a different look usually means a different valve. A wall-hung toilet needs a steel carrier frame inside the wall, which makes it a renovation rather than a swap.

Low-flow fixtures also depend on the house. They need adequate supply pressure and clear drains. A low-flow shower head on weak pressure gives a poor shower, and a low-flow toilet on an old, rough drain line clogs more. If pressure is already a problem, water pressure troubleshooting comes first.

Upgrades that involve another trade

Several upgrades need power as well as water. A heated bidet seat, a touchless faucet with a plug-in adapter and a motorized whole-house shut-off each need an outlet close by. Beside a sink or toilet that outlet should be GFCI-protected, and adding one is a licensed electrician's job.

Water heaters are the largest example. They are not among the ten plumbing jobs we work on, so describe yours and ask about it when you call or text. An electric tankless heater needs a very large electrical supply, often new circuits and sometimes a bigger service. Newfoundland and Labrador has no natural gas network, so gas heaters here burn propane. A propane heater, tank or tankless, is installed under the CSA B149.1 code by a qualified gas technician, with its own venting. Newfoundland and Labrador has no natural gas, so a gas water heater here burns propane. If you smell gas near one, leave at once, touch no switches on the way out, and phone 911 or the propane supplier from outside.

Upgrades for cold weather and leaks

Frost-free outside taps suit the climate here: St. John's is commonly cited as one of the windiest and wettest major cities in Canada. Besides those taps, quarter-turn valves at the main and under each fixture close in one movement when something lets go, where an old multi-turn valve may not close at all. In a house that often stands empty, leak sensors near the toilets, sinks and water heater can close a motorized valve on the main when one gets wet. The valve needs power, so a battery backup matters during outages. Where pipes have frozen before, pipe repair in St. John's covers protecting and rerouting them.

FAQ

Fixture upgrade questions

How does a modern toilet's water use compare with an old one's?

Toilets from a few decades ago commonly used 13 litres or more a flush, while current models use about 6 litres and high-efficiency ones about 4.8. Dual-flush toilets add a lighter flush for liquids. On an old, rough drain line a low-flow toilet can clog more often, so it is worth knowing the drain's condition before switching.

Will a new shower valve stop the temperature swinging when someone flushes?

Yes, if it is a pressure-balancing or thermostatic valve; current codes call for that kind of scald protection in new showers. The valve sits inside the wall, so changing it means opening the wall from the front or from an access panel behind, and the handle and faceplate change with it. A valve that already leaks or drips is the natural moment to make the change.

What is the rough-in, and why does it matter for a new toilet?

It is the distance from the finished wall behind the toilet to the centre of the drain flange, which you can measure to the bolts that hold the toilet down. Most are 12 inches; some older homes have 10 or 14. A toilet made for one rough-in will not sit properly on another, so measure from the wall itself, not the baseboard, before you buy.

Does a bidet seat need an outlet beside the toilet?

Only if it is heated or powered. A plain bidet seat takes water from the toilet's supply through a tee fitting and needs no power. A heated or electric seat needs a GFCI-protected outlet within reach of the toilet, and adding one is a licensed electrician's job. An extension cord across a bathroom floor is no substitute.

Is a frost-free outside tap worth fitting here?

In a climate with long freezes, usually. Its long stem puts the valve inside the heated wall, and the part outdoors drains empty when the tap is closed. It works only if the hose comes off before winter. A hose left attached holds water in the stem, which can freeze and split it inside the wall, where the leak shows up in spring.

Book plumbing fixture upgrades in St. John's

Call, text or send the form, Mon to Sat, 8:00 am to 7:00 pm.