Skip to main content

Plumbing hours: Mon to Sat, 8 am to 7 pm

Plumbing from $80

5.0 out of 5.Rated 5.0 on Google

5.0 out of 5.Rated 5.0 on Google

Plumbing

Toilet Repair & Installation St. John’s NL

Toilet repair and installation in St. John’s, booked as plumbing from $80, starts with what sits under the toilet. In an older house that may be a cast-iron flange, a bend of lead pipe and a floor that has settled out of level. In a newer one, it is a plastic flange on flat plywood.

  • Starting at $80
  • Mon to Sat, 8 am to 7 pm
  • Call or text, no account needed

Book toilet repair and installation

No account needed. HomeBrill calls or texts you back to set a time for the visit.

Plumbing starts at $80. When HomeBrill calls or texts you back, ask about the price of your job before a time is set. Privacy: see the privacy policy. This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

Toilet repair and installation in St. John's: white two-piece toilet between a fold-down grab bar and a grab bar holding the toilet paper Toilet repair and installation in St. John's: white two-piece toilet between a fold-down grab bar and a grab bar holding the toilet paper

What sits under a toilet in an older house

Every toilet bolts to a flange, a ring fixed to the floor over the drain, with a wax or foam seal between the two. That hidden part is where an older house and a newer one differ most.

In a newer house the flange is usually black ABS plastic, glued into the drain and screwed to a plywood subfloor. A house of the older kind may have a flange of cast iron or brass, joined to a cast-iron stack by a short bend of soft lead pipe. Its floorboards may have moved over many decades. The basement usually shows which you have: black plastic, or heavy dark pipe with wide joints. When a toilet in an older house leaks at the base or will not sit firm, the fix starts below the porcelain.

Old floors that have moved

Wooden houses settle. The bathroom floor of an older house may slope, dip toward the middle of a joist span, or carry layers of flooring added by one owner after another. A toilet has to sit level and bear evenly on its base; set on a slope, it rocks, strains its seal and holds its tank water lower on one side. Old layers of flooring can also leave the flange too low or too high for the seal to do its job.

A floor that has gone soft around the base is a different matter. It is the mark of a seal that leaked for a long time. The damaged wood is cut out and replaced with sound subfloor before any toilet goes back on it.

Cast iron, lead and measurements that are not standard

An old cast-iron flange that has rusted thin is rarely chipped out, as the first question below explains. A lead bend is soft enough to dent or split when a toilet is pressed down onto it, so it is handled gently. When it has to go, it is cut out and replaced with plastic, joined to the old cast iron by a coupling made for that joint.

Older bathrooms can also hide a measurement a new toilet does not expect: a drain set further from the wall than the usual 12 inches, or closer to it. Toilets are still made for the less common distances, and an offset flange can shift the outlet a short way where the difference is small. Plumbing fixture upgrades explains how to measure before buying.

Booking toilet work in St. John’s

Toilet repair starts at $80, and a new flapper is a different job from a cracked flange. Tell HomeBrill what you can see and get a price before a time is set. The plumbing line is open from 8:00 am until 7:00 pm, Monday to Saturday: phone or text (709) 910-9100, or use the booking form at the top of this page.

Say roughly how old the house is, whether the floor gives underfoot, and whether the basement ceiling under the bathroom is open. Until the visit, close the valve behind the toilet. In an older house it may be a stiff multi-turn valve, so turn it gently. If it will not close, use the main shut-off where the water line comes into the basement. HomeBrill’s plumbing page covers the tub, shower and sink in the same room and lists all ten plumbing jobs.

See also drain cleaning and unclogging in St. John’s.

Problems and parts

Inside the tank: running, refilling and weak flushes

Toilet repair and installation for toilets that run, refill on their own, need two flushes, rock or leak at the base, and new toilets set on a fresh seal. Most toilet faults sit inside the tank, and most of them are repairs.

Lift the tank lid and a toilet explains itself. The handle lifts the flapper, the tank empties into the bowl, the flapper drops back, and the fill valve refills the tank until the float tells it to stop. A toilet that runs or hisses has lost one of those steps: the flapper is not sealing, or water is trickling into the overflow tube.

Look at the water line first. If it sits above the mark inside the tank, lower the float. Then look at the chain: it needs a little slack, and a chain caught under the flapper holds it open. If the toilet still refills on its own, the flapper is the likely cause, and the food colouring test in the questions below confirms it.

Weak flushes are often scale in the rim holes under the bowl’s lip and in the siphon jet at the bottom. A toilet that clogs often is a drain question as much as a toilet one, covered by drain cleaning and unclogging; never pour a chemical drain opener into a toilet.

St. John’s is commonly cited as one of the foggiest major cities in Canada, and on damp days a tank of cold water can sweat enough to wet the floor. An insulating liner inside the tank reduces it. HomeBrill’s plumbing service lists the nine other plumbing jobs it takes on.

What you notice, and the usual causes

Runs on and on between flushes
A worn or warped flapper, a chain too short or caught under it, a float set too high, or a failing fill valve.
Weak flush, or two flushes needed
The tank’s water level set low, rim holes and the siphon jet furred with scale, the wrong flapper for the toilet, or a partial clog.
Tank fills slowly
Grit in the fill valve, or a stop valve left partly closed.
Water around the base
A failed wax seal, loose closet bolts, a cracked flange or a crack in the bowl.
Toilet rocks when you sit on it
Loose bolts, an uneven floor or a broken flange; the movement soon breaks the seal.
Drips between the tank and the bowl
A worn tank-to-bowl gasket, or tired rubber washers on the tank bolts.
Clogs often
Too much paper, wipes, an early low-flow design, or a partial blockage further down the line.

Parts and materials involved

  • Flapper The rubber seal at the bottom of the tank that lifts to flush; sizes and shapes vary by toilet.
  • Fill valve Refills the tank after a flush and shuts off at the set level.
  • Float Tells the fill valve when the tank is full; its height sets the water level.
  • Flush valve and overflow tube The opening the flapper seals, and the pipe beside it that stops the tank overfilling.
  • Tank-to-bowl gasket and bolts Seal and hold the tank of a two-piece toilet on its bowl.
  • Wax ring or wax-free seal Seals the toilet’s outlet to the flange, and is never used twice.
  • Closet bolts Hold the toilet down to the flange through its base.
  • Flange The fitting on the drain that the toilet bolts to; a repair flange or ring mends a broken one.

Pricing

From a flapper to a new toilet: what the price depends on

We repair and install toilets as plumbing work, so the $80 plumbing starting price is where a toilet job begins. A repair inside the tank is the small end of it; anything that means lifting the toilet adds steps. Say what the toilet is doing and whether there is water on the floor, and ask about the price when you call or text.

A flapper, a fill valve or a handle is changed with the toilet in place. Water at the base means lifting the toilet to renew the seal, and a cracked flange adds a repair. A new toilet is a bigger job again: the old one comes off, the flange is checked, and the new one is assembled, set and connected.

Plumbing starts at
$80
Your job
Describe it when you call or text, and ask about its price before a time is set

toilet repair and installation

Setting a toilet: the flange, the seal and the floor

A toilet is only as good as what it sits on. Before buying a new one, measure the rough-in, the distance from the finished wall to the centre of the closet bolts, so the new toilet fits the drain. Plumbing fixture upgrades explains the measurement and the lower-flow models.

When the old toilet comes up, the flange has to be sound, fixed firmly and at the right height for the finished floor. A seal is never reused, so a lifted toilet goes back on a new wax ring or wax-free seal and new closet bolts. It is then levelled with shims so it cannot rock, the bolts are snugged without cracking the porcelain, and a new supply line goes on.

Toilets are heavy and porcelain breaks into sharp edges, so lift with care, and with the toilet off, stuff a rag into the open flange to keep sewer gas out. A toilet moved to a new spot needs its drain moved too, a change that may need a permit, so ask your city or town first.

When a toilet is worth replacing

The parts inside a tank are made to be changed, so a toilet with a sound bowl and tank can be kept going for many years. A crack in the bowl or the tank is different: porcelain cracks can open suddenly, so a cracked toilet is replaced, not patched.

Age alone is no reason to replace one. Better reasons are a crack, or a flush that stays weak after the parts and rim holes are dealt with. Frequent clogs on an early low-flow model, or an old toilet that uses far more water a flush than a current one, are others.

Service areas

Toilet repair and installation are booked in St. John’s, Mount Pearl, Paradise, Conception Bay South and the Goulds, as the service areas page sets out.

FAQ

Questions about toilets in older St. John’s houses

Can a new toilet go onto the old cast-iron flange in my house?

Often, if the flange is whole, sits level and still grips the bolts. One that has rusted thin or lost a bolt slot can take a metal repair ring screwed down over it. A new flange made to fit inside the old pipe also works. Which suits is decided with the toilet up and the old wax scraped off, since only then can the flange be seen.

There is lead pipe under my toilet. Does it affect the drinking water?

No. A lead bend under a toilet carries waste away from the house, while the water you drink arrives through separate supply pipes. Whether an old house still has a lead service pipe from the street is another question, and the City of St. John’s can help answer it. Leave the bend alone unless it leaks, wash your hands after touching it, and never heat or sand it.

Should the toilet come up when a bathroom floor is retiled?

Yes. Tiling around a toilet leaves a cut edge at its base and a flange sitting lower than the new floor. With the toilet out, the tile runs underneath, the flange is brought up to suit with an extension ring, and the toilet goes back on a new seal and bolts. In an older house it is also the moment to check the subfloor around the drain.

My old house has a sloping bathroom floor. Can a toilet sit level on it?

Usually, within limits. Plastic shims slid under the low side of the base level the toilet and stop it rocking; wood shims are avoided because they rot if they get wet. Trimmed flush and hidden behind a bead of caulk, they do not show. Where the slope is too steep for shims to bridge, the floor around the flange is built up level first, so the toilet and its seal sit square.

My toilet refills by itself every so often. What is going on?

Water is seeping past the flapper into the bowl, so the fill valve keeps topping up the tank. A few drops of food colouring in the tank prove it. Do not flush, and if colour shows in the bowl within about a quarter of an hour, the flapper is leaking. A new flapper that matches the toilet’s flush valve is the usual repair.

Why does it take two flushes to clear my toilet?

Too little water is reaching the bowl, or with too little force. The tank level may sit below the mark inside the tank, or scale may be clogging the rim holes and the siphon jet. A replacement flapper that does not suit the toilet may be closing too soon, or a partial clog may sit in the trapway or the line beyond it.

What does water on the floor around the toilet mean?

If it appears after flushing, the wax seal under the toilet has probably failed or the bolts have loosened. Drips beading the outside of the tank on a humid day are condensation. A hairline crack in the bowl can also leak at the base. A failed seal lets waste water and sewer gas through, so deal with it soon.

Is a toilet that rocks a problem?

Yes, more than it seems. Rocking usually means loose closet bolts, an uneven floor or a broken flange, and every movement works the seal loose until it leaks. Snugging the bolts gently may cure it. If it rocks again, the toilet is lifted, the flange checked and the toilet reset on a new seal with shims.

Book toilet repair and installation in St. John’s

Call, text or send the form, Mon to Sat, 8:00 am to 7:00 pm.